How to Make a Reclaimed Wood Card & Photo Display

-

November is a favorite time of year at our house. It signifies the holidays, a time when we both enjoy sending out and receiving seasonal greetings from our friends and family. Like many, we enjoy keeping these cards out on display to add to our holiday decor. This year we created a card stand using an antique salvaged wood beam we'd recently come across.

Reclaimed_Wood_Christmas_Card_Display_eHow

Video of the Day

Things You’ll Need

  • Wood beam or board, 34 inches by 4 inches

  • Hammer

  • Yardstick or tape measure

  • Clamps

  • Circular saw

  • Low-grit (or finer) sandpaper

  • Compressed air (optional)

  • Low-odor clear finishing spray

  • Felt furniture protectors

We found and worked with a salvaged antique wood beam measuring 34 inches in length by 4 inches in width and depth. Similar wood beams can be found at a local salvage yard or warehouse. For those without access to antique finds, the same concept could apply to a new board or beam from the hardware store.

Step 1

Cut the wood to match the above dimensions or follow the same steps below on a different sized beam to create a custom look.

Reclaimed_Antique_Wood_Beam_eHow

Step 2

Prep the wood by removing any jagged splinters or exposed nails. Decide which sides will display best as the front and top portions (these will be in the most direct path of sight), and then position and clamp it to a workbench to hold it steady for measuring and sawing.

Removing_Nails_With_Hammer_eHow

Step 3

To create the display you'll want to make two even and slightly angled cut lines into the board. The angles will help display the cards better, and the front cut should be slightly deeper than the rear, to help create a tiered effect.

Measure the top width of the board, marking two even lines at least 1 inch apart with a pencil. For example, for our 4-inch wide board, we made marks on the 1-inch and 3-inch marks.

Measuring_Wood_eHow

Step 4

Make the same marks along the opposite end, and then use the straight edge of a ruler to connect each mark, resulting in two parallel lines along the top of the board. These lines will act as the guide for making cuts.

Drawing_Line_Cuts_eHow Measuring_Cut_Lines_eHow

Step 5

To make a tiered effect, the front-facing cut should be deeper than the rear-facing cut; ¼-inch difference in depth between the two will achieve a nice balance. First decide which side of the board will be front-facing, and then adjust the circular saw to a ½-inch depth on a 15-degree angle. Next, make an even cut down the top of the board, using the pencil line as a guide.

Circular_Saw_eHow

Step 6

Repeat on the rear-facing line after readjusting the circular saw to a ¼-inch depth on a 15-degree angle.

Using_a_Circular_Saw_eHow

Tip

If using a wider beam, make three or more cut rows following the same 15-degree angle and making each progressive cut with a ¼-inch difference in depth.

Step 7

Clear the beam of sawdust and use a sheet of low-grit sandpaper to smooth each side and edge of the wood.

Sanding_Wood_Beams_eHow

Tip

Using a can of compressed air will help clear away small debris from the freshly cut lines in the top of the beam.

Step 8

In a well-ventilated area, apply three thin and even layers of a low-odor clear finishing spray, which will not only help provide a permanent protective finish but will also prevent any residual debris crumbling from the wood once inside.

Clear_Finishing_Spray_eHow

Step 9

Allow the finish to completely dry, about three hours, before adhering heavy-duty felt discs at each corner on the underside of the beam. These discs will provide protection against surface scratches where the card stand will be displayed.

Felt_Discs_eHow

A stand like this would work well on a mantle, entryway console table or even as a focus centerpiece along a buffet.

Display cards by sliding them into the cut lines, staggering to show breadth and variety. Tall, vertical cards work well on the back row, and smaller, horizontal cards display well on the front row.

Meaningful_Christmas_Cards_eHow

To kick off the decorating season, we pulled out a few of our favorite holiday cards we have saved over the years from dear friends who sent handmade greetings or from close relatives who have since passed. After sliding them into the card stand, we nestled a few fresh trimmings from our holly tree around the beam to create a festive mantle display.

DIY_Wood_Holiday_Card_Stand_eHow

As new greetings arrive throughout the season and make their way into the card stand, the look and feel of the display will evolve and change, which keeps it fun.

Outside of the holidays, this card stand could be used to display a rotation of family photos or a mix of greeting cards throughout the year.

Share this article

Recent posts

Teachers’ Top Needs for 2019

0
Teachers’ Top Needs for 2019Great classrooms don’t happen by accident. Teachers across the country work hard to build vibrant, energizing learning environments for their students, which often means ev

Top Tips to Transition Back to Work After Baby

0
Top Tips to Transition Back to Work After BabyMany new parents spend hours preparing for the arrival of a new baby – reading books, seeking professional advice and consulting friends and family. Howev

Get Away Without Going Away

0
Get Away Without Going Away5 family staycation ideas that won’t break your budgetFamily vacations are a great way to bond and take a step back from the hectic schedules that accompany everyday life, b

5 Common Questions for Memorializing a Loved One

0
5 Common Questions for Memorializing a Loved OneOne of the most difficult conversations in a person’s life typically takes place near the end of that life. Planning for a funeral can put an emotional

Boat Safe

0
Boat SafeEnsure your boat is ready for the water with this checklist No matter how much experience you have on the water, prepping your boat – and your passengers – before leaving the dock can make fo

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Recent comments